BuildTak GeckoTek EZ-Stik Cold Build Surface (Single Sheet) 250mm x 220mm

BuildTak Polyetherimide (PEI) printing sheets are a terrific upgrade for any 3D printer. These sheets help 3D printed parts stick to the bed while printing, while making removal of your finished parts a breeze. The BuildTak PEI Build Surface is ideal for materials that could are typically more difficult to remove from the print bed, such as PETG. Combine your BuildTak PEI Sheet with a FlexPlate System for ultimate ease in 3D print removal, and easily swap between BuildTak Original and PEI with an Extra FlexPlate!

Availability: Currently Unavailable
Add to wishlist
Product No. M-USH-LSPP
Build Surface Area (in): 8.66" x 8.66"
6.5" x 6.5"
19.7" x 19.7"
13.07" x 13.39"
12" Diameter
9.25" x 9.25"
9" x 10"
4.5" x 4.5"
8.66" x 8.66"
8" x 8"
12" x 12"
10.2" x 13.9"

CHOOSE THE BEST PRINT SURFACE FOR THE JOB

BuildTak Polyetherimide (PEI) Build Surface sheets adhere to your 3D printer’s print bed, or onto your BuildTak FlexPlate with the same no-cleanup BuildTak Original adhesive. The PEI sheets are comparable to BuildTak’s Original printing surface, but exhibit slightly different adhesion and release properties, which vary from material to material. In general, BuildTak Original sheets will offer a stronger grip of your 3D prints to the 3D printing surface, whereas BuildTak PEI sheets will offer even easier release of finished 3D prints. It is a great alternative to PEI or Kapton Tape. Combine your BuildTak PEI Sheet with a FlexPlate System for ultimate ease in 3D print removal, and easily swap between BuildTak Original and PEI with an Extra FlexPlate!

After prolonged use, you may find that you need to clean your BuildTak surface with some isopropyl alcohol (or soap and water) to renew its adhesion abilities. Allow to dry completely. If your BuildTak sheet becomes damaged, just replace it with a new one!

Questions View All Responses

Is it possible to get a 220 mm X 270 mm or 8.66 in by 10.62 in Variant of this??

Add Response

Is this compatible with the Raise3d Pro2 Plus build plate?

Add Response

Will this work for MakeIt Pro-L?

Add Response

Whats the temperature limit on these? I have one and im getting bubbles between the spring steel and the build surface while printing ABS, I have my bed temp at 100°C

View 1 Response

Hi, is this different from the Flexplate system or is it replacements for the Flexplate system? Is this removable or will it stay adhere to the aluminum plate? I am looking to upgrade from blue tape to something a bit less wasteful. Thanks!

View 1 Response

Does this one fit to AnyCubic Mega-X?

View 1 Response

Can these be cut? I have a new sovol01 and it has a different bed size than the ones you sell 300x280

View 1 Response

I have a BIQU Thunder printer. The heated printbed is 12"x12". So the Printer Build Surface is all I need to order? 3-pack is too many but that's OK.

View 2 Responses

Any problem with this fitting the 300x300 build area of a Wanhao Duplicator 9 MK 2? Also how are they applied to the existing build surface and are they easily removable?

View 1 Response

Does this fit the Raise N2 Plus Printer? I heard they require 13x13.

View 1 Response

could i use these on the Lulzbot taz 6

View 1 Response

Can I use induction sensors with buildtak?

View 1 Response

Could these sheets to be used on for the Z18 Makerbot machines? Also, do they have any adhesive in the back of them to adhere to the build plate?

View 1 Response

Is there a specific temperature the heated bed needs to be cooled to for part removal? Or is that based on the filament rather than the bed material?

View 1 Response

does this work with PLA

View 1 Response

Do I still need to apply ABS slurry to help ABS stick?

View 1 Response

How thick is it? 12 x 12

View 1 Response

Ask a question about this product

Back to top