E3D E3D All-metal v6 HotEnd Fully Assembled - 1.75mm Universal (with Bowden add-on) (12v)
All of the benefits of the v6 HotEnd Full Kit without all the hassle of putting it together! These fully assembled v6 HotEnds are ready to go: the heater cartridge and thermistor are inserted and tested, and the heater block and nozzle are heat-tightened.
The v6 contains the same signature high-temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments.
| List Price: | $85.00 |
|---|---|
| Price: | $85.00 |
| Price: | $... |
| Availability: | Only 3 left in stock. |
| Order Now: | Ships Tomorrow Free U.S. Shipping |
The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder - this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations.
With High-Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon - this also eliminates HotEnd meltdown failures that are common with PTFE designs. Even though the v6 has a PTFE liner inside the hotend the liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating. Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate.
The v6 has cut back on a bunch of bulk. This clean-cut version's overall length is only 62mm, and there are significant reductions in the X/Y dimensions by using the new injection molded fan duct.
Are you eager to start printing right away? Good. So are we - and that's why here at MatterHackers we praise the v6 HotEnd. No adhesives, Kapton tape, or soldering is needed to get started. The new v6 simply locks into place with a little screw, high-temp glass sleeving is used to insulate the thermistor legs. This makes installing the hotend (as well as removing) a quick and smooth process compared to earlier methods involving various adhesives. The parts of the hotend just screw together, and the fan duct naturally clips in - this can be manipulated in different ways to suit your setup preference.
Check out that accuracy!
The v6 has kept its vivid thermal transition that promotes high-quality printing - this is a standard requirement with all E3D accessories and hotends. A sharp thermal break gives excellent control over material output, which provides more precise starts and stops during your extrusion. Essentially, as a printing aficionado, this means you will have a more authentic and keen print.
Everyone likes to have different options to fuel their creative fire. Well, another reason why the v6 HotEnd is at the head of its class is that it has multiple nozzle sizes to choose from, thus your printing dreams are limitless. The default nozzle is 0.4mm, which produces fantastic prints with a great level of speed, ease, and resolution. Collecting a plethora of nozzle sizes increases your ability to explore and experiment with different filaments and extrusion settings.
The printing options are endless with multiple nozzles!
Included (Fully Assembled):
Metal parts:
- 1 Aluminium Heatsink (Contains embedded fitting for tubing in 1.75mm Universal and 3mm Bowden versions)
- 1 Stainless Steel heat break
- 1 Brass Nozzle (0.4mm)
- 1 Aluminium Heater Block
- 1 100K Semitec NTC thermistor
- 12v 30W Heater Cartridge
- 1 12v 30x30x10mm fan
- 1 High-Temperature Fiberglass Wire - for Thermistor (150mm)
- 2 0.75mm Ferrules - for Solder-Free Wire Joins
- 4 Plastfast30 3.0 x 16 screws to attach the fan to the fan duct
- 1 M3x3 socket dome screw and M3 washer to clamp thermistor
- 1 M3x10 socket dome screw to clamp the heater block around the heater cartridge
- 1 Fan Duct (Injection Moulded PC)
The new Bowden coupling system sits entirely within the hotend, which means that there is no need for two separate 1.75mm products for Bowden users and Direct users. Instead, it has a 1.75mm Universal product that has the internal couplers installed. Direct users just use a short length of tubing to line the filament down into the hotend, and Bowden users can simply use a longer piece of tubing with a coupler to fix the other end to their extruder.
- Find a way to attach the hot end. This usually involves printing some kind of mounting piece.
- Modify your firmware configuration.
- Find a way to power the fan.
- How does my hot end attach to the printer?
- Can I modify my printer's firmware?
- If you want to use the Chimera, Cyclops, or Kraken, you must also consider how many motor drivers, thermistor inputs, and heater outputs your controller board has.
- Does my printer use 1.75 or 3 mm filament?
- Does my printer run on 12 V or 24 V, or some crazy combination of the two (i.e. a 24 V PSU with the hot end throttled down to 12 V using PWM)?
- Is my printer a direct drive or Bowden setup?
Questions
is this suitable for the anycubic mega s 3d printer?
can you use this with robo3d r1 plus?
Besides printing out some parts, is there anything else I need to purchase for a CR-10S to get this to work?
WILL THIS HOTEND WORK ON THE ANYCUBIC MEGA PRO.. SPECIFICALLY WILL ALL THE CONNECTOR FIT . SO I CAN JUST PLUG IT IN AND ITS READY TO GO
Is the one that comes in the Pulse XE?
Can I pay extra to have the necessary 3D printed mount included in the kit?
Will this work on the “Homers”/Tevo Tarantula Pro?
What is the best way to incorporate the E3D system with a QIDI X PLUS (direct drive)?
will this work with a FLSUN kossel delta printer? thanks
Can you get this hotend with a different E3D nozzle diameter?
Do you have any hotends that would work for XYZ Da Vinci Jr. 3 in 1?
Question will the Fully Assembled version work with the Rostock Max v2? the link beside the rostock max is for the non assembled one. just want to be sure before I buy. Also can you still buy the E3D Hotend Mount and Fan Shroud all ready printed ? The link in the comment is dead, and I am not able to print in ABS right now.
Good Day! Can this hot end heat up to 265 degrees celsius? Thanks
Can I request this pre-assembled with a different size nozzle?
Will this hotend work on a Jgaurora A5 printer?
Would this work on a direct drive extruder?
I have install the E3D V6 with bowden connect on my Creality which is running Marlin 1.1.8 from Tiny Machines. I start to print and after the first layer is complete the printer stops with an error message "E1 Thermal Runaway, Please reset". How do I correct this problem? Is there a change to the firmware needed for the new type of thermistor?
Newbie here... You stated earlier to find a new mount on Thiniverse, But can you advise me which one would be the best one to print for this Hot End?
will this work on the Geeetech A 30.
Is it possible to buy the 3D printed parts for the CR-10S with the Heat-Set Inserts added?
Do you offer a fully assembled kit which includes a volcano block?
I'm trying to build my own (bowden type) 3D printer from scratch, what are the overall dimensions of the hot end assembly?
Will this work on an MP mini select v2?
Since these have the new cartridge style thermistor as answered in a previous question do they need the breakout board as referenced here? https://e3d-online.com/V6-PT100-Sensor-Kit
Hello, does this work for anycubic i3 mega?
Is.compatible with Creality CR-10?
Does this have the new cartridge thermistor?
Do you still have to do the final tightening step in the assembly guide, or is that completed as part of purchasing the assembled version?
Is the fan 12v or 5v?
do you have a E3D hot end that will work with Ultimaker Original+
Is this suitable for the anycubic mega s? Do I need to do something else if yes?