Sinterit Sinterit Polypropylene Fresh SLS Powder (6kg)

SINTERIT POLYPROPYLENE FRESH 

Advanced Polypropylene (PP) Material: Prototyping and Functional Uses

PP material with good mechanical properties. Dedicated for prototyping of PP parts, as well as functional parts utilizing chemical resistance, weldability and ductility.

Key Features of the Sinterit PP:

• Great chemical resistance
• Low density enabling buoyancy
• Recyclable
• Suitable for pneumatic applications
• Can be welded to other PP parts

Example Applications for Sinterit PP:

• Automotive: Reservoirs, Piping, Housings
• Plastic Part Producers: Integrate SLS parts with Injection Molded parts
• Laboratories: Custom Chemical Tools such as holders or vessels
• High quality, low volume production of low stress parts
• General prototyping of PP parts

---

Which Lisa Compact SLS 3D Printers are compatible with Sinterit Polypropylene (PP)?

How do Sinterit's SLS Powders Compare to Each Other?

What are the Technical Specifications of Sinterit's PP?

GENERAL
Technology	Powder for Selective Laser Sintering (SLS) 3D Printing
Material Type	PP co-polymer
Dedicated for	Lisa PRO, Lisa X, NILS 480
Software	Sinterit Studio Advanced
Material refreshing ratio¹	50%
Color	Grey
Nitrogen Needed	No
MECHANICAL PROPERTIES
Tensile Strength	19.3 MPa
Tensile Modulus (Young)	820 MPa
Flexural Strength	25.6 MPa
Impact Strength Charpy Method (unnotched)	29.8 kJ/m2
THERMAL PROPERTIES
Melting Point	135°C

¹ Refresh ratio is the amount of refreshing powder required to be mixed after a print with unsintered material.

Information provided within this document shows values for reference and comparison only. Parameters presented in this specification are subject to change without notice. Final part properties may vary based on a printed part design and orientation, material handling as well as printing environment (humidity and temperature). The manufacturer is responsible for validation whether the printout is accurate and fit for the intended purpose.

---

Frequently Asked Questions

WHAT IS A REFRESH RATE?

• In the context of Sinterit products, refresh rate is the ratio of the minimum amount of fresh powder needed in a mixture of material used in an SLS 3D printer. The lower the refresh ratio, the better the cost-efficiency of the material.

HOW DO I REUSE USED PP POWDER?

• Reuse leftover PP powder on your next print by adding 50% of PP Fresh Powder. By mixing 50% used PP with 50% PP Fresh, you will create a cost-effective, 100% print-ready PP powder.

WHAT IS THE DIFFERENCE BETWEEN “Fresh” POWDER AND “Starter” POWDER?

• Powder Type	Condition	Description
  Starter	Print-Ready	Powder that's ready to print. (i.e. no need to mix used and fresh powder, it's ready to be poured into the machine and start printing)
  Fresh	Fresh	Powder that's for refreshing the powder. Mixing this with Used Powder will turn it into Print-Ready.
  	Used	Powder leftover from printing, present in overflow bin or remaining after printout cleaning.

HOW DO I MIX "Used" and "Fresh" POWDER?

• Powder Handling Stations or a Powder Sieve can help mix used and fresh powders.
  • The amount of needed fresh powder is automatically calculated by the software and shown on the printer screen after the print job is finished. Just add shown amount of material into the mixing cycle of used material and you can start your next job with refreshed material.

HOW SHOULD I STORE THE PRINTING POWDER?

• Store the powder at room conditions ( ~23°C and 50% humidity – the lower humidity the better)
• Always store the material in a sealed dry box/container.
• Do not leave the container open.
• Clean the machine directly after printing and store the material immediately after removing the print cake.
• Do not let the powder stay in the printer for more than a couple hours.
• Put a few silicone absorbers in the container (but don’t add them to the printer)

DO I NEED AN ATEX VACUUM CLEANER TO CLEAN POWDER?

• Yes. SLS polyamide powder used for 3D printing is considered particulate matter because of its size. Polyamide powder particles are generally 40 micrometers or smaller. If vacuumed in an ordinary vacuum cleaner, the powder could cause an explosion.

  Such materials are subject to labor regulations on air quality and occupational safety. The procedures call for appropriate maintenance of powder at work. Only certified industrial vacuum cleaners should be used to clean such materials.